Belt (Mechanical)

Fig 1. Power Transmission Belt

Introduction

Belts are used for transmitting power between two shafts. Belts will be of two kinds, flat and vee belts. Belts are running over the pulleys which are mounted on two shafts. Belts are used when the distance between the shafts is large. Gears are used when the distance between the shafts is small.

Types of Belts

File:Belt types.jpg

Fig 1. Belt Types

• Flat Belt - This belt has a rectangular cross section as shown in fig 1. (a) . These belts are capable of transmitting power over long distances between pulley centres. The efficiency of this drive is around 98% and produce little noise.

• V Belt - This belt is used with grooved pulleys, V-belts are trapezoidal in cross-section as shown in fig 1. (b). This belt permit large speed ratio and can transmit higher power.
• Circular Belt - This type of belt has a circular cross-section as shown in fig 1.(c). and is used with the grooved pulleys.

Types of Belt Drive

Open Belt drive

Cross Belt drive

Compound Belt drive

Open Belt drive

Open Belt drive consists of two pulleys A and B in fig 2. Driver pulley is the pulley which is keyed to the rotating shaft. Driven pulley is the pulley which is keyed to the shaft and to be rotated. Here Driver pulley is pulley A and Driven pulley is pulley B.

The mechanical power or rotary motion is transmitted from the driving pulley to the driven pulley because of the frictional grip that exists between the belt and the pulley surface.

File:Open Belt Drive.jpg

Fig 2. Open Belt Drive

The driver pulley A pulls the belt from the lower side and delivers it to the upper side. Thus the tension in the lower side of the belt will be more than the tension in the upper side. Lower side is called as tight side and the upper side is called as the slack side.

Sometimes in a belt-drive, there is always a possibility of some slipping taking place between the belt and the pulleys which cause the driven pulley to rotate at a lesser speed, consequently reduces the power transmission. Hence belt drives are said to be not a Positive type of power transmission system

Velocity Ratio :

Velocity ratio is the ratio of the velocity of the driven to the velocity of the driver.

Let N₁= Speed of the driver in r.p.m ; d₁= Diameter of the driver

N₂= Speed of the driven in r.p.m ; d₂= Speed of the driven

Length of the belt passing over the driver in one minute = circumference of the driver X number of revolutions per minute

= π d₁ X N₁

Length of the belt passing over the driven in one minute = circumference of the driven X number of revolutions per minute

= π d₂ X N₂

Length of the belt passing over the driver in one minute = Length of the belt passing over the driven in one minute

π d₁ X N₁ = π d2 X N2

Velocity ration is ${\frac {N_{2}}{N_{1}}}={\frac {d_{1}}{d_{2}}}$ --------- equation (1)

Slip of the belt

When the driver pulley rotates , due to the firm grip between the pulley surface and the belt, the driver pulley carries the belt. The firm grip between the pulley and the belt is obtained by friction which is known as frictional grip. But sometimes the frictional grip is not sufficient which may cause some forward motion of the driver pulley without carrying the belt with it. This means that there is a relative motion between the driver pulley and the belt. The difference between the linear speeds of the pulley rim and the belt is a measure of slip. Generally slip is expressed as a percentage

Creep of the belt

In a belt drive the belt is passing over the driver and driven(follower) pulley. Belt is subjected to tension during the power transmission. The portion of the belt which leaves the follower and approaches the driver is known as the tight side of the belt and is subjected to tension T₁. The portion of the belt which leaves the driver and approaches the follower is known as the slack side of the belt and is subjected to tension T₂. T₁ > T_{2 .} Stretch in the belt due to different tensions on the two sides of the pulley will be different. A certain portion of the belt when passes from slack side to tight side, extends and the same portion contracts again when it passes from tight side to slack side. Due to these changes in length , there will be a relative motion between the belt and the pulley surfaces which is known as Creep. The creep reduces slightly the speed of the follower (driven pulley).

Cross Belt drive

File:Cross Belt Drive.jpg

Fig 3. Cross Belt Drive

In an open belt drive both the pulleys rotate in the same direction, where as in cross belt drive the pulleys rotate in the opposite direction.

The driver pulley A in fig 3. pulls the belt from CD side and delivers it to FE side. Thus the tension in the belt CD will be more than that in the belt FE. CD side is known as tight side and FE side is known as slack side.

Compound Belt Drive

File:Compound Belt Drive.jpg

Fig 4. Compound Belt Drive

Compound Belt drive is used when the power is to be transmitted from one shaft to another through a number of pulleys. In fig 4. shows Compound belt drive where in pulley 1 drives the pulley 2 . Pulleys 2 and 3 are fixed to the same shaft, hence the pulley 1 drives pulley 3 also. Pulley 3 drives the pulley 4.

Velocity Ratio of Compound Belt drive.

Velocity ratio is the ratio of the velocity of the driven to the velocity of the driver.

Let N₁= Speed of the pulley 1 in r.p.m ; d₁= Diameter of the pulley 1

N₂= Speed of the pulley 2 in r.p.m ; d₂= Speed of the pulley 2

N₃= Speed of the pulley 3 in r.p.m ; d₃= Speed of the pulley 3

N₄= Speed of the pulley 4 in r.p.m ; d₄= Speed of the pulley 4

From equation (1) Velocity ratio of pulleys 1 and 2 is

${\frac {N_{2}}{N_{1}}}={\frac {d_{1}}{d_{2}}}$ ------- (i)

Similarly Velocity ratio of pulleys 3 and 4 is

${\frac {N_{4}}{N_{3}}}={\frac {d_{3}}{d_{4}}}$ -------- (ii)

Multiplying the equations (i) and (ii)

${\frac {N_{2}}{N_{1}}}X{\frac {N_{4}}{N_{3}}}={\frac {d_{1}}{d_{2}}}X{\frac {d_{3}}{d_{4}}}$

N₂ = N₃ as the pulleys 2 and 3 are fixed to the same shaft.

${\frac {N_{4}}{N_{1}}}={\frac {d_{1}}{d_{2}}}X{\frac {d_{3}}{d_{4}}}$

which is

${\frac {Speed\ of\ last\ follower}{Speed\ of\ first\ driver}}={\frac {Product\ of\ diameter\ of\ drivers}{Product\ of\ diameter\ of\ followers}}$

See Also

पट्टा(बेल्ट)

External Links

• Belt Friction
• Slip and Creep